(1) The power supply of ultrasonic cleaning machine and electric heater shall be well grounded.

（2）超聲波清洗機嚴禁在槽中沒有水或溶劑時，千萬不要啟動，造成空振，造成振動頭報廢或損壞。

(2) It is forbidden to start the ultrasonic cleaning machine when there is no water or solvent in the tank, so as to cause air vibration and scrapping or damage of the vibrating head.

（3）有加熱系統的清洗設備嚴禁無液時打開加熱開關。

(3) For cleaning equipment with heating system, it is strictly forbidden to turn on the heating switch when there is no liquid.

（4）禁止用重物（鐵件）撞擊清洗缸缸底，以免能*轉換器晶片受損。

(4) It is forbidden to strike the bottom of the cleaning cylinder with heavy objects (iron parts) to avoid damage to the converter wafer.

（5）超聲波發生器電源應單獨使用一路220V/50Hz電源并配裝2000W以上穩壓器。

(5) One 220V / 50Hz power supply shall be used separately for the power supply of ultrasonic generator, and a voltage regulator above 2000W shall be equipped.

（6）清洗缸缸底要定期沖洗，不得有過多的雜物或污垢。

(6) The bottom of the cleaning cylinder shall be washed regularly without excessive sundries or dirt.

（7）清洗機操作過程中請勿將手指放入清洗槽中，否則會感到刺痛或者不適。

(7) Do not put your fingers into the cleaning tank during the operation of the cleaning machine, otherwise you will feel tingling or discomfort.

（8）每次換*液時，待超聲波起動后，方可洗件。

(8) When changing * liquid every time, wash the parts after the ultrasonic starts.

（9）采用清水或水溶液作為清洗劑，一定要禁止使用酒精，汽油或任何可燃氣體作為清洗劑加入清洗機中。

(9) Clean water or aqueous solution shall be used as cleaning agent. Alcohol, gasoline or any combustible gas shall not be used as cleaning agent to add to the cleaning machine.

（10）當直接使用易燃液體清洗時，要盡量在短時間內完成清洗工作，并要求操作者不要離開現場。

(10) When directly cleaning with flammable liquid, try to complete the cleaning work in a short time, and ask the operator not to leave the site.

（11）當需要用腐蝕性或揮發性強的清洗液時，可采用間接清洗的方法。即：在清洗槽內加水，再將所需清洗液倒入適宜的容器內并放入被清洗物，然后將裝有清洗液和清洗物的容器浸入清洗槽中，即可開始清洗工作，其效果與直接清洗相同。

(11) When corrosive or volatile cleaning solution is needed, indirect cleaning method can be adopted. That is: first add water in the cleaning tank, then pour the required cleaning solution into a suitable container and put the cleaned object, and then immerse the container containing cleaning solution and cleaning object into the cleaning tank to start the cleaning work. Its effect is the same as that of direct cleaning.

（12）使超聲波清洗效果更好的方式，超聲波清洗槽的溫度為30~50℃，根據不同的清洗對象正確選擇清洗劑。清洗劑一般分為水基（堿性）清洗劑、溶劑清洗劑和化學反應清洗劑。通常使用水基清洗劑，根據被清洗物的污染程度和污垢性質，選用不同的清洗時間。

(12) The temperature of ultrasonic cleaning tank is 30 ~ 50 ℃, and the cleaning agent is correctly selected according to different cleaning objects. Cleaning agents are generally divided into water-based (alkaline) cleaning agents, solvent cleaning agents and chemical reaction cleaning agents. Generally, water-based cleaning agent is used, and different cleaning time is selected according to the pollution degree and dirt nature of the cleaned object.

（13）在使用時禁止先開機后倒入清洗液，這樣會使機器損壞。

(13) When in use, it is forbidden to start the machine first and then pour in the cleaning fluid, which will damage the machine.

（14）清洗物品不要直接放在清洗槽底部，應用專用清洗支架清洗筐，這樣有利于提高清洗效果。

(14) Don't put the cleaning items directly at the bottom of the cleaning tank. Use a special cleaning support to clean the basket, which is conducive to improving the cleaning effect.

（15）盡量避免長時間連續工作，一般不超過30分鐘為宜。

(15) Try to avoid working continuously for a long time, generally no more than 30 minutes.

（16）在使用時槽內清洗或脫氣的溶液不要放入過少，一般在槽內2/3處更好。

(16) When in use, do not put too little cleaning or degassing solution in the tank, which is generally better at 2 / 3 of the tank.

以上就是為大家介紹的有關層超聲波清洗機價格http://m.chinalssc.com的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務

The above is the price of ultrasonic cleaning machine for relevant layers http://m.chinalssc.com I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service