清洗機是一種同時能清洗和干燥的設備，整個清洗過程是程序化操作，使用起來非常方便；同時也能降低能源的消耗和玻璃儀器的破損率；能保證有效的清洗能減少交叉污染和提高實驗的可靠和真實的數據。

　　A cleaning machine is a device that can clean and dry simultaneously. The entire cleaning process is programmed and very convenient to use; At the same time, it can also reduce energy consumption and the damage rate of glass instruments; Ensuring effective cleaning can reduce cross contamination and improve the reliability and authenticity of experimental data.

　　整個清洗過程大概分為：預洗、清洗、漂洗、最終漂洗、和干燥，在每個階段的時間和溫度都可以調整，清洗機本身帶有標準操作程序，同時用戶根據所清洗的物品進行程序化設定，并可以經過驗證后設為標準程序。

　　The entire cleaning process can be roughly divided into pre washing, cleaning, rinsing, final rinsing, and drying. The time and temperature at each stage can be adjusted. The cleaning machine itself comes with a standard operating procedure, and users can program it according to the items being cleaned, which can be validated and set as a standard procedure.

　　隨著清洗機長時間使用，清洗機內零部件磨損積垢，長期不進行維護極易造成化學清洗泄露嚴重，干燥過濾器臟容易被堵，蒸汽疏水器堵升溫慢、溫度壓力模擬量零點漂移誤報警等情況。

　　As the cleaning machine is used for a long time, the internal components of the cleaning machine wear and accumulate dirt. Long term lack of maintenance can easily lead to serious chemical cleaning leaks, dirty dry filters that are prone to blockage, slow heating of steam traps due to blockage, and false alarms due to temperature and pressure analog zero drift.

　　實驗室中常用的清洗機，隨著長時間凈置塵埃懸落，導致過濾效果下降，微生物易超標，無法保證清洗效果；電磁隔離閥膜片結垢，閥門漏水，膜片內漏，微生物滋生影響清洗效果；腔室清洗架密封磨損，造成密封泄漏，影響清洗效果等。

　　The commonly used cleaning machines in the laboratory, with prolonged exposure to dust, result in a decrease in filtration efficiency, and microorganisms are prone to exceed the standard, making it impossible to ensure cleaning effectiveness; The fouling of the electromagnetic isolation valve diaphragm, valve leakage, internal leakage of the diaphragm, and the growth of microorganisms affect the cleaning effect; The sealing of the chamber cleaning rack is worn, causing seal leakage and affecting the cleaning effect.

　　常見維保內容有：

　　Common maintenance contents include:

　　1.高效過濾器定期更換

　　1. Regularly replace high-efficiency filters

　　2.DOP完整性檢漏測試

　　2. DOP integrity leak testing

　　3.初效過濾器定期更換

　　3. Regularly replace the primary filter

　　4.電磁隔離閥清洗、更換

　　4. Cleaning and replacement of electromagnetic isolation valve

　　5.腔室清洗架密封更換

　　5. Sealing replacement of chamber cleaning rack

　　6.蠕動泵潤滑

　　6. Lubrication of peristaltic pump

　　7.打印機頭更換

　　7. Printer head replacement

　　02

　　02

　　通過式清洗機常見維保內容：

　　Common maintenance contents for through type cleaning machines:

　　1.高效過濾器定期更換

　　1. Regularly replace high-efficiency filters

　　2.DOP完整性檢漏測試

　　2. DOP integrity leak testing

　　3.初效過濾器定期更換

　　3. Regularly replace the primary filter

　　4.壓縮空氣氣管、閥島更換

　　4. Replacement of compressed air pipes and valve islands

　　5.隔膜閥更換

　　5. Diaphragm valve replacement

　　6.UV燈更換

　　6. UV lamp replacement

　　7.門密封更換

　　7. Door seal replacement

　　03動物籠清洗機常見維保內容：

　　03 Common maintenance contents of animal cage cleaning machine:

　　1.電磁隔離閥更換

　　1. Replacement of electromagnetic isolation valve

　　2.滾輪更換

　　2. Roller replacement

　　3.加熱盤管清洗除紅銹

　　3. Clean and remove red rust from the heating coil

　　4.蠕動泵泵頭更換

　　4. Replacement of peristaltic pump head

　　針對以上三種清洗機類型維?？偟膩碚f可分為兩大項：

　　Overall, maintenance for the three types of cleaning machines can be divided into two main categories:

　　1.首先確認清洗機的型號種類，依據型號查看對應的關鍵部件診斷清單。將可能存在問題的節點及部件逐一排查，確定清洗機整體情況，更換過濾器、清洗噴淋臂、更換何處O型圈、更換蠕動泵硅膠管等。

　　Firstly, confirm the model and type of the cleaning machine, and check the corresponding diagnostic list of key components based on the model. Inspect the nodes and components that may have problems one by one, determine the overall condition of the cleaning machine, replace the filter, clean the spray arm, replace the O-ring, replace the peristaltic pump silicone tube, etc.

　　2.其次進行電氣測試、三相電測試、單相電測試、IO測試、測試屏幕、測試打印機、溫度校準復核以及壓力校準等，確認維保之后清洗機正常運作，并觀察改進情況。

　　2. Next, conduct electrical testing, three-phase electrical testing, single-phase electrical testing, IO testing, screen testing, printer testing, temperature calibration review, and pressure calibration to confirm the normal operation of the cleaning machine after maintenance, and observe the improvement situation.

　　本文由 通過式清洗機  友情奉獻.更多有關的知識請點擊  http://m.chinalssc.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from the through type cleaning machine For more related knowledge, please click http://m.chinalssc.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.